Carburetor Set MXT RACING Carburetor 17.5mm with Intake Manifold, Manual Choke
for Horizontal Minarelli
Carburetor Set MXT RACING Carburetor 17.5mm with Intake Manifold, Manual Choke
for Horizontal Minarelli
- Description
- Fitting
Description
Carburetor Set MXT RACING 17.5 mm with Intake Manifold Black PHBN Type with Manual Choke Compatible with Minarelli Horizontal
The MXT-RACING carburetor set with a nominal diameter of 17.5 mm is designed as a pre-tuned tuning carburetor in PHBN design with a manual choke. It is intended for setups with a horizontal Minarelli engine, particularly when a DellOrto PHBN carburetor is already installed and a change within the same design is to be made. Final tuning is carried out via the main jet.
Product Features:
- Carburetor set with 17.5 mm carburetor and intake manifold
- Carburetor type PHBN with manual choke
- Factory pre-tuning, adjustment via main jet required
- Connections available: Gasoline, Oil, Vacuum, Overflows
- OEM No. for comparison purposes: 3067
- Delivery includes open intake manifold
The design as a pre-tuned PHBN carburetor aims for easy installation and a straightforward tuning process via the main jet. The included open intake manifold is relevant for setups where the carburetor mount needs to be properly matched, while the jet tuning adjusts the mixture preparation to the cylinder, air filter, and exhaust.
Technical Details:
- Design: Slide Carburetor
- Nominal Diameter: 17.5 mm
- Carburetor Type: PHBN
- Choke: Manual
- Connections: Gasoline, Oil, Vacuum, Overflows
- Reference Number: 3067
- Main Jet Type for Fine Tuning: M6
Since the carburetor is factory pre-tuned, adjustments in practical operation are made via the main jet. This is technically relevant because the main jet significantly influences the fuel quantity in the upper load range, which is crucial for clean engine running and controlled thermal loading.
Vehicle and Model Compatibility:
- Designed for Minarelli horizontal
- Change particularly suitable if a PHBN carburetor is already installed
- Use possible with 50 cc and 70 cc cylinders
The actual suitability depends on carburetor mount, intake manifold, and the implementation of choke operation on the vehicle. Crucial is whether the PHBN design and the existing intake and connection concept fit the vehicle setup.
Installation and Application Notes:
- With an existing DellOrto PHBN carburetor, a change to the same design is possible
- Check choke cable and routing before installation
- Adjust main jet after installation to cylinder, air filter, and exhaust
- Check engine running after tuning for clean idle and throttle response
- For fine tuning, M6 main jets are used
Tuning Guideline Values Without Guarantee, For Reference Only:
- 50 cc Cylinder, Air Filter and Exhaust Original: Set 1 M6 50 to 72
- 50 cc Cylinder and Air Filter Original: Set 2 M6 70 to 92
- 50 cc Cylinder with Sport or Racing Air Filter: Set 3 M6 80 to 102
- 70 cc Cylinder with Air Filter Original: Set 3 M6 80 to 102
- 70 cc Cylinder with Sport or Racing Air Filter: Set 4 M6 88 to 110
The mentioned jet ranges are relevant for selecting a starting point for tuning, but they do not replace vehicle-specific adjustments. Only precise jetting ensures the appropriate mixture formation and thereby influences engine performance, throttle response, and thermal stability under continuous operation.
Note for Checking Before Purchase:
- Please check before purchase whether a compatible PHBN mount is available on the vehicle and whether choke operation and connection concept (gasoline, oil, vacuum) fit the existing setup. Since final tuning is done via the main jet, a matching with cylinder, air filter, and exhaust is required.
Quick Info: Carburetor - Installation, Adjustment & Tuning
Installation: Mount carburetor without tension, check intake manifold and gaskets for leaks, adjust throttle cable smoothly, ensure fuel supply (gasoline, oil and vacuum).
Basic Setting: Mixture screw usually 1.5 - 2.5 turns open, idle screw adjusted for stable idle, always tune engine when warm.
Tuning:
- Main Jet = Full Throttle / High Load
- Needle Position = Partial Load & Acceleration
- Pilot Jet = Idle & Starting (typically does not need to be changed)
Control: Check Spark Plug Condition
- white = too lean
- black = too rich
- brown = optimal
Important: After changes to air filter, exhaust or cylinder, a new carburetor adjustment is mandatory.
About the Manufacturer MXT
MXT is the powerful proprietary brand of Heavy Tuned and stands for high-quality replacement and tuning parts for motorcycles, scooters, and gear mopeds.
As a reliable alternative to OEM parts, MXT offers a wide range of cylinder kits, carburetors, and crankshafts to variator components, body parts, and batteries. The products impress with solid workmanship, precise quality, and a strong price-performance ratio.
Ideal for riders looking for durable replacement parts and tuning components for many vehicle models.
Technical data
Global | |
|---|---|
| Item number |
MXT-VE-650.001-SET
|
| Manufacturer | MXT |
| Net weight | 494 g |
| Reference OE/OEM Number | 3067 |
| Type | Intake manifold, Carburetor |
| Version | PHBN |
| Size | 17,5 mm |
Carburetor | |
| Carburetor diameter | 17.5 |
Engine | |
| Carburetor diameter in mm | 17.5 |
Ratings
5
4
3
2
1
Loading reviews...
Delete review
Product safety information
Information about the manufacturer
| Product | Carburetor Set MXT RACING Carburetor 17.5mm with Intake Manifold, Manual Choke for Horizontal Minarelli |
| Manufacturer |
Heavy - Tuned GmbH |
| Responsible person |
Heavy - Tuned GmbH Seilschlagstr. 6 31311 Uetze Hänigsen Germany |